Posted December 3, 20159 yr For a while I have wanted to make a small 4x4 with independent suspension so as soon as this contest was released I went to work and have come up with this so far. IMG_5136 by JJ2Sam, on Flickr It has 4x4 drive with a center differential and a V2 piston engine. IMG_5138 by JJ2Sam, on Flickr The front suspension was inspired by Efferman's 11 stud wide independent suspension but I have to make improvements to the steering (working on that). IMG_5139 by JJ2Sam, on Flickr Here you can see the center diff, the 16t to 20t hooks the front diff to the center and the rear diff is connected through the power ball joint. IMG_5140 by JJ2Sam, on Flickr The rear suspension is nothing special if you were wondering. IMG_5137 by JJ2Sam, on Flickr Money shot! More updates coming soon! All feedback is appreciated! Hope you like it so far. Bye.
December 3, 20159 yr So far so good! Looking forward to see how it develops...and after that evolves into model B...
December 3, 20159 yr Looks cool so far! Personally id try to fit a bigger fake engine (dont think a transverse i4 would fit right?) and go for a lancia rally car style body (Delta Integrale, a martini livery would be pretty doable and visually interesting)
December 3, 20159 yr Author So far so good! Looking forward to see how it develops...and after that evolves into model B... Looks good so far! What are you thinking of doing for the B Model? I think the B model might be a quadcopter using the wheels as fans. Looks cool so far! Personally id try to fit a bigger fake engine (dont think a transverse i4 would fit right?) and go for a lancia rally car style body (Delta Integrale, a martini livery would be pretty doable and visually interesting) I tried to put a transverse engine in it but I could not figure out how to connect it to the "drive shaft"
December 3, 20159 yr I think the B model might be a quadcopter using the wheels as fans. I tried to put a transverse engine in it but I could not figure out how to connect it to the "drive shaft" Yeah, looking at the front width i think you *might* be able to fit three cylinders and have a gear off the crank running underneath the engine, but im ignoring the liftarms/bricks on the side of the engine, and the height would be a BIG issue. I think in most FWD/FE cars the engine is slightly in front of the front axle, with the diff connecting to the gearbox on the rear-side, and you might be able to use the crown wheels of the front-diff to transmit power rearwards, but this would make the front quite bulky, and eliminates the possibility for a center diff (meaning front and rear axle are locked) I wonder if anyone has ever done a good transverse FE/FWD MOC, most big cars i see here are RE/RWD or RE/AWD or use longitudinal V8 engines to a center mounted diff.
December 3, 20159 yr If your B model is not a car, it might be hard to fit in some of those specialized pieces.
December 3, 20159 yr Every time I'm impressed, how tight some of you can build - that's something I need to learn. Impressive build, can't wait to see the next steps
December 3, 20159 yr This one looks like some heavy duty vehicle! I wonder how it'll transform to B-model
December 4, 20159 yr I think the B model might be a quadcopter using the wheels as fans. Sounds very interesting! I'll be following your entry closely then
December 4, 20159 yr Author If your B model is not a car, it might be hard to fit in some of those specialized pieces. Yes it will! But I have a use of the differentials in mind. Every time I'm impressed, how tight some of you can build - that's something I need to learn. Impressive build, can't wait to see the next steps Actually I am trying to make it tighter to supply room for an interior, I think it would look weird it there was just a random steering wheel and so seat. This one looks like some heavy duty vehicle! I wonder how it'll transform to B-model Like I said before it is going to be a quadcopter.
December 7, 20159 yr Author Update time! IMG_5163 by JJ2Sam, on Flickr Since the last "update- start" I have added seats, a (WORKING) steering wheel, and I completely redid the front drive chain. IMG_5164 by JJ2Sam, on Flickr IMG_5166 by JJ2Sam, on Flickr Here you can see the steering wheel and the gear that connect the steering wheel to the new rack and pinion steering. IMG_5167 by JJ2Sam, on Flickr This is how I connected the front drive to the center diff. That's about it for this update. All the pictures are on my flickr account Thanks for reading!
December 7, 20159 yr Looking very snug and compact-what sort of bodywork are you going to put on it? Also, that idea of a quadcopter as a B-Model certainly has me interested.
December 8, 20159 yr Author Looking very snug and compact-what sort of bodywork are you going to put on it? Also, that idea of a quadcopter as a B-Model certainly has me interested. I dont know what body to put on it but I usually just start throwing panels on stuff and hope it looks good
December 17, 20159 yr Author Update time! DSCF0032 by JJ2Sam, on Flickr DSCF0036 by JJ2Sam, on Flickr Since the last update as you can tell I have done some bodywork. I have finished all but the rear and some of the interior styling. DSCF0035 by JJ2Sam, on Flickr I tried to go with a sleek look on the back with vertical lights and inward curved panels. DSCF0034 by JJ2Sam, on Flickr The side is quite plane but I don't know what to do to make it look better. Well that's about it for this update. Stay tuned for more! All the photos are on my photostream. Hope you enjoyed!
December 20, 20159 yr I think this would be great in a style like the Local Motors Rally Fighter... Edited December 20, 20159 yr by Technyk32231
December 20, 20159 yr Author Yes it would but that would mean a complete body redesign to make it look right Also I realized that it had no windshield, how did I not notice that
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.