Corrado

This is a super nice B model. Looks very clean, congrats!

Hello everyone, I recently completed the Yellow Hot Rod, a car roughly in a 1:10 scale, not based on any specific design. The build centers around an adjustable front suspension that I developed some time ago, adding a unique functionality to the hot rod. Given the model’s size, I was able to incorporate additional features that I hope you’ll find interesting for this type of car. The biggest flaw is that the car only runs on a single power function M motor, but it is safe due to its low mass and high gear ratio. An L motor (or two) would be much better, which I believe would be doable with a bit more time. Check out the specs below: Size: Length: 37cm / 14.6inch Width: 20cm / 7.9inch Height: 13cm / 5.1inch Weight: 1kg / 2.2lbs Features: Openable doors & trunk Easily removable bodywork Front adjustable suspension & rear live suspension Motorized with a fake V8 engine 2x M Motor 1x BuWizz 2.0 I encourage you to check out the video to see the suspension in detail and watch the car in action!

I love the robustness, especially the gear covers. What about stability with such a high center of mass?

I dont know too but if it's already I hope that will give us new intresting parts.

I've always loved your constructions, that"s why I can't weit.

I hope that this series will offer more interesting parts in the future, but so far what it offers is not very satisfying.

Yes, but this topic is focusing specialy on technic part of Forma. I don't see any new parts excluding paper skin...

Hi, what you think about new LEGO Forma? We have 3 new sets which are the same inside but with 3 diffrent skins. It's premium LEGO series that's why it will cost nearly 50 dolars.

Thanks but unfortunately no... Thank you!

Thank you. Yes litlle damage in driving axels. That because i want to get 4 studs high rear suspension, now I have better ideas for this part of a car. Thank you too. I dont have one jet but if you want I can do it. High of swingarms are 4 studs high. I do it like for better reconstruction of a car. 3 studs high it's a bit to little for this model in this scale. Yes, I agree. Small turnables are good for suspension.

Thank you!

Today I want to show you my newest and fastest ever car. Ariel Nomad British light weight car based on twin brother Ariel Atom - one of the fastest road cars. Nomad like buggy cars have only rear wheel drive. During construction I recived also BuWizz brick for review . I decided to put it in the vehicle and show the diffrence between Power Function and BuWizz when presenting new model. It allowed to increase its power and simultaneous weight loss. Technical data: -Lenght 29cm -Width 18cm -Height 13cm -Weight 810g (Buwizz) -2x XL motors -1x Servomotor -1x Extension cable -Buwizz or small BatteryBox + IR tower In my car, I tried to reproduce the best possible vehicle mechanical construction. It has a independent suspension which on the driven rear axle turned to be a quite a challange in medium size scale. In my model I dont use differential to bulid drivetrain. Power is transmitted directly with a ratio 3:1 from two XL motors. Despite small size of BuWizz I failed to put fake engine, but I am happy with weight of car because it was possible to have weight under one kilogram. For me, Buwizz is the most practical third party controling brick. It offers everything in one practical case. My only small objection is the inability to use gaming pad to steering but I think that it will be possible in the future. Some photos: Flickr for more: https://www.flickr.com/photos/142980798@N05/sets/72157673238594798/with/29638046247/ I am also invite you to see trailer: If you like this Subscribe me with notification. Enjoy!

For me it doesnt look too good, especially with that high suspension but I see it gives lot of fun. :)

I know that now you add some support on sides, but it is now strong enough? On video can be seen how the structure is trembling. Crazy size and good idea!

Very good idea to use container from other set. Waiting for competition.