THIS IS THE TEST SITE OF EUROBRICKS!
Search the Community
Showing results for tags 'sportcar'.
Found 5 results
-
Hello :) Topic for placing in one place my self-made products 8pin wide in the scale of Speed Champions. Pleasand viewing! I will be glad to comments with wishes and criticism :)
-
Hello! Im glad to present my new model for LEGO Technic Porsche contest. I hope it will be published soon at rebrick =) Porsche Carrera GT Features: - 1:10 scale - realistic Carrera GT V10 piston engine in mini scale - full independent suspension - rear wheel drive - HOG steering with working steering wheel - openable door, hood and trunk - rising rear spoiler Video below shows some of these functions. I recorded very simple video just for the contest, without any titles and sounds. -
Hello All! Recently i've finished experiments with my second drift car (the first one drifted not too good). Please watch a video before you'll estimate its holed design :) Thanks for watching!
-
Hey! I have to say that this is my first lego supercar, as i'm more used to trial trucks and trophy trucks. I worked on this one for about three months and the goal was to get a supercar over 1kg, wich I barely passed. First, some overall pictures of the car. Yea, I know, i've got some pretty bad panel gaps around the rear wheels and the whole back of the car isn't too great but it actually was built for the functions. Moving on to the manual functions the car has: Opening hood revealing the RTC system (locking) Opening butterfly doors Opening engine bay cover (locking) +the whole rear lifting in 2 sections to provide access to the BuWizz (large one is also locking) One huge challenge was to get a curved roof at such a small scale, wich you can see in more detail here: It's also fully suspended, front is independent with MacPherson and rear is pendular. I guess I could've squeezed something independent in the rear too but it was too little space and I was running out of time. Functions powered by BuWizz (wich is located behind the rear axle) Drive with an L motor, working V8 engine Steering with an M motor, working steering wheel Linear 2-speed gearbox integrated in the chassis powered by an M motor Here's a little game: Try to find all the motors in the car. Also, I would like to know what do you think about it. -
Hello All! Some time I was out from EB, but I’ve come back with new MOC :) I had short of time that’s why its construction took about two monthes. This is my tuning-version of legendary Ferrari Enzo. The scale is 1:8.5 (length – 58.5 cm, width – 24 cm, height – 13 cm), total weight – 3.6 kg. Design combines various features of original Ferrari, tuning-versions Edo Competition, MIG-U1 and my own ideas. There are six RC functions in it: - moving – 2 x XL; - acceleration – 2 x XL; - two-stage gearbox (pneumatic-controlled) – 1 x Servo; - adders locking (pneumatic-controlled) – 1 x Servo; - steering – 1 x Servo; - clearance adjustment (four large pneumatic cylinders) – 1 x M. The scale is approximate with respect to wheels. Front wheels – 81.6 mm from 42000, rear – more aggressive tires from 8461. The transmission differs from original one. For better playability and transmission load decreasing i’ve mounted AWD. In the same time central differential gear is an output gear of gearbox. Two-stage gearbox allows to drive both on the flat surface and on slight off-road. I’ve mounted two air tanks to decrease switching time. The acceleration is realized on adders (two parallel circuits for reliability increasing). The adders can be locked. Instead of velocity locked adders sums the torque. The next feature of my model is adjustable clearance on both axles (original Ferrari Enzo has only front axle lift). Vertical rods was replaced by shock absorbers and pneumatic cylinders are mounted at horizontal angle. There is an adaptive aerodynamic element in my model – it is rear spoiler that is switched simultaneously with gear box. The model has detailed cabin The movie: Thanks for watching!
