October 30, 20213 yr I wonder how many people started the Ball Factory, but never got it working properly.
October 30, 20213 yr @Ankoku i have done a complete file for the invisible lift, if you need it its on rebrickable
October 31, 20213 yr GBC Vertical Ball Lifts without using a reversing unit. IMG_8365 ====================================================== It proved not possible to increase the lift range by using longer crank arms as it would put too much side thrust into the tower guide beams causing jamming. How to increase the lift height ? Another way of raising the ball lift box had to be found. Mk 1 version with higher lift range. A vertical tower was built to give a lift range of 57 L. Old Lego large chain links were used in a loop with 9T chain sprockets at top & bottom. IMG_8399 IMG_8400 The ball lift frame is connected to the chain by a 3L beam & a swinging link, with the chain driven by an L motor to the bottom sprocket wheel. Testing proved that the ball lift frame Raising & lowering OK. When tested with a 30 ball load the 3L beam kept disengaging from the chain. The 3L beam is a push fit onto a the two studs of the large Lego link. IMG_8398 One possible option was to glue it to the link but instead I decided to come up with another better solution. So Mk 1build abandoned. Mk. 2 Vertical ball lift (WIP) A more secure way of connecting the lift frame to the chain was needed. This time I used Lego 5L wide chain links with medium sprocket wheels top & bottom. Also required to be able to lift 30 balls per cycle. Lift range now 66L The arm with the swinging link was much easier & stronger to connect to the chain using two black pins inserted into the link with two short black rods pushed into the pins to lock them in place. IMG_8401 More progress to follow and a video once completed. Edited October 31, 20213 yr by Doug72 spelling, removed text
October 31, 20213 yr You should probably add a video. Although isn't this more appropriate in the Akiyuki train thread?
October 31, 20213 yr 53 minutes ago, Ankoku said: You should probably add a video. Although isn't this more appropriate in the Akiyuki train thread? Mk 2 version not finished yet and will be stand alone driven by PF L motor. The ball release at top has yet to be made & installed with a return for balls vis a zig zag chute. A video of the Mk 2 version will be made when completed & Tested. The train version got me thinking how to increase the lift height. Edited October 31, 20213 yr by Doug72
October 31, 20213 yr 17 hours ago, Ankoku said: I wonder how many people started the Ball Factory, but never got it working properly. count me in. Finished this 5-6 months ago but never took a video. Cup2Cup v1.2.1 Bucket Wheel Tower (4 bucket version) Edited October 31, 20213 yr by dunes video added
November 1, 20213 yr Akiyuki style Spiral Lift Reservoir. Can hold easily 200+ balls. Edited January 10, 20223 yr by dunes
November 1, 20213 yr For my Ball Factory at the moment, I have used longer tubes and only rotates 540 degrees on the spiral lift.
November 17, 20213 yr Hi guys, I finished Akiyuki's Basket Shooter earlier this week, following the instructions by djm and Blakbird - many thanks to those two guys for their time and effort in producing the instructions. A really enjoyable build and satisfying in the end. After some tuning, it runs well, with just one issue. The far right (blue) shooter module, never has enough power to get any ball to even reach the basket. On a full spring wind (as full as you can before the actuator starts to shoot the ball backwards) it only gets about two thirds to the basket. The other two shooters are fine and are scoring enough hoops to please me. I've checked and checked the blue shooter module, and everything looks correctly built. I just wondered if anyone else has had a similar issue, with a lower powered shooter module? The only thing I can think of is the black 9.5L shock absorber (soft spring) maybe a bit odd, and am waiting for another couple of spares to swap out and try. Any other ideas from the GBC experts here would be most welcome.
November 18, 20213 yr 3 hours ago, ostrichwatch said: Hi guys, I finished Akiyuki's Basket Shooter earlier this week, following the instructions by djm and Blakbird - many thanks to those two guys for their time and effort in producing the instructions. A really enjoyable build and satisfying in the end. After some tuning, it runs well, with just one issue. The far right (blue) shooter module, never has enough power to get any ball to even reach the basket. On a full spring wind (as full as you can before the actuator starts to shoot the ball backwards) it only gets about two thirds to the basket. The other two shooters are fine and are scoring enough hoops to please me. I've checked and checked the blue shooter module, and everything looks correctly built. I just wondered if anyone else has had a similar issue, with a lower powered shooter module? The only thing I can think of is the black 9.5L shock absorber (soft spring) maybe a bit odd, and am waiting for another couple of spares to swap out and try. Any other ideas from the GBC experts here would be most welcome. yes i had the same issue with my build too and yes its related to the shock absorbers, i find that some are stiffer to compress than others
November 18, 20213 yr Thanks 9v for the reply 👍 It's nice to have confirmation. Hopefully one of the new springs I've ordered will work. I'll report back once they arrive. Currently blue has yet to score ! 🏀
November 28, 20213 yr @Ankoku i have currently finished the step module but im having some jamming issues at the input of the spiral lift. did you finish the file for the improved version?
November 28, 20213 yr @9v system Not quite finished, but finished enough for you! :) I will up it for a short time for you!
November 28, 20213 yr 1 hour ago, Ankoku said: @9v system Not quite finished, but finished enough for you! :) I will up it for a short time for you! thanks, i tried to fix the issue with the current design and its just not working, i do like the input ramp though
November 28, 20213 yr thanks for the file @Ankoku i have made some changes already. reverted some parts back to the instruction version as i dont want to buy some of the other parts, i changed the slopes in the hopper to how DJM has them in his cup to cup module
December 7, 20213 yr Does anyone have a studio file of the box to box module? I have the instructions but not the file.
December 12, 20213 yr not sure if anyone posted these here but Takanori hashimoto has come up with two really nice modules inspired by akiyukis gbcs, he has instructions for both which i have purchased
February 13, 20223 yr this was out GBC layout at brickvention. the Akiyuki ones with the exception of the planets, catch and spin and five rings were mine, built from all new parts, i used motors from aliexpress and they held up well esp the mouldking ones.
March 5, 20222 yr On 2/17/2021 at 3:45 AM, aeh5040 said: I did offer to help make instructions from photos... your in luck, myself and @Ethan M are working on instructions for it, i have finished my part, and the module section is ready, just need to do the gearbox
July 14, 20222 yr greetings all, all the files for the Akiyuki project are now fully digitized and are available for download thanks to @Jude The Lego Dude for helping me with some of these https://bricksafe.com/pages/gbcbuilder/akiyuki/akiyuki-project-files
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.