heyitsdisty Posted April 17, 2017 Posted April 17, 2017 25. Name: THUMPER Category: Cat B (IR receiver) Dimensions: 29 x 24 x 18 Signature move: Disc spinner uppercut Functions: Two M drive motors and one XL weapon motor, all operated with IR remote control and powered with a AAA battery box. Rubber band suspension on front wedges, keeping them flat to the ground and reducing ground clearance. Topic:
teos Posted April 17, 2017 Posted April 17, 2017 26. Cat. B: PF IR Name: La Grange 3001 Signature move: Tongue Spinner Size: 39l x 20w x 12h Weight: 1663g Motors: 2L, 2M, 2 receivers, 1 battery box The idea was to make a marbled "Grangemouth" 3001 brick. The controller requires two hands to operate, though I only had one. The other was holding my phone to video. 20170416_205655 by topazard, on Flickr 20170416_205706 by topazard, on Flickr Link to work in progress post:
pangniadek Posted April 17, 2017 Posted April 17, 2017 27. Cat: A Name: Harvester of Sorrow Signature move: Weapon: Super Ultra High Speed Mega Blast Titanium Spinning Drum Defens: Steel Rope and Poison Hook Size: 32 x 33 x 8.5 (studs) I admire your robots from the very beginning and I want to congratulate you on each of your ideas and solutions. A little fear with my 7 hours building: HoS is a two-sided robot that shreds everything that's on the way! The spinning drum absorbs the blocks at full speed, and the rear rope blocks the opponent's movements by twisting into his wheels and mechanisms (breaks loose). This is not a big robot, but it's fast (2x M Motor) and nimble. Forum link: And remember .. Respect is everything;)
Wilbero79 Posted April 17, 2017 Posted April 17, 2017 28. Deathclaw Cat B: PF IR receiver Spins of Death (signature move) It has two M motors with "sticks" on them that spin rather fast, it is also powered by two L motors which control the craft, as well as making it spin with it's 6 full battery boxes
Erik Leppen Posted April 17, 2017 Posted April 17, 2017 29. Entry name: Wimbledoom Category: Cat B: PF IR Signature move name: Dual horizontal hammers Short summary of the functions: Control: 1 battery box, 2 receivers, 2 remotes, 4 M motors Drive: M motor for left wheel; M motor for right wheel Weapon: M motor for releasing the hammers; M motor for returning the hammers Images: Video: Discussion topic:Wimbledoom - Discussion topic
JTS Posted April 17, 2017 Posted April 17, 2017 30. Name: Mr CuddlesCategory: B - PF IR Signature Move: Grab 'n' StabWeapons: Large claws grip the opponent so they can't escape, then a powerful axe smashes them from abovePower: 2x Battery Boxes, 2x IR Receivers, 2x XL motors for drive, 1x L motor for axe, 1x M motor + 2x LAs for clawsDimensions: 45L x 40W x 18H studs (in idle mode) Claws extend to 60 studs wide to ensure even the largest opponents cannot escape Thick all-round armour plating protects all essential functions and components Ride height is less than 0.5 studs and the centre of gravity is very low down to protect Mr Cuddles from flipper-bots Quick and agile, despite weighing 1.85 kg Battery boxes are easily accessible for quickly replacing flat batteries ( see video) Other features: Intimidating name 12 sharp horns (possibly venomous!) The link to the discussion topic is here, and more images including some WIP can be found here. I hope you enjoy!
AVCampos Posted April 18, 2017 Posted April 18, 2017 31. Here is my entry, Devil's Tongue. Category: Cat B (PF IR) Signature move: Devil's Spoon Functions: it has four-wheel drive powered by two XL motors, and can move upside down. The flipper, "Devil's Spoon", is spring loaded. It has a mechanism that uses a single motor to pull the flipper down and release it, via differential and clutch. The rounded sides, as well as the capability of upside down drive, prevent it from getting stranded by the adversary. Here are some images: Here is a video of it in action: The discussion topic can be found here:
The Vooduist Posted April 18, 2017 Posted April 18, 2017 32. My first entry Claw-Crawler CAT A: sbrick plus (not using sensors) Signature move- Quick claw (propelled by buggy motor for quick grabbing or tearing apart bots) Size: L45 studs W29 studs (drill and spoiler were taken off for the final model due to length) Propulsion: 2xl motors for driving/steering and 1 buggy motor for the claw Description: This is my Claw-Crawler, a slow but very powerful battle bot tank built to grab its enemies. Then, if in a related battleground area (just like on the real deal) were they have the hammer, drills grinders, and etc it would destroy them by using the weapons on the battleground by driving them into the death sentence traps! Also due to its massive torque it can crawler over other bots and squish them. This was designed for powerful side or top impacts. If you design your battle bot correctly and can take 3-6 whacks were the battery box is and detach it, it mite do something but the crawler will still run just not as fast (it is unlikely that it would knockout the robot). The drill and spoiler are NOT in the final bot. Inside size to 45 studs (Barely) Good luck everybody! Discussion:
Recommended Posts