Posted April 19, 20186 yr Finally, after a hard fight during assembly and a strong decision to change the my presentations look ! Challenger MT 865C + Kinze 1050 (1) by Michał Skorupka (Eric Trax), on Flickr CAT Challenger 865C Challenger's story began 25 years ago. They were the first and remain the only tractor designed and constructed especially for working on caterpillars. The Model 700 combines traction with low ground pressure, which ensures the highest performance and simultaneous soil protection. The 800 series tractors from the technical assumption correspond to their smaller counterparts, however, they are larger and heavier machines with a maximum power of 646 hp. Drive and steering: As I wrote earlier, the model is driven and controlled by a sub-tractor consisting of two different types of old type. The XL motor is responsible for the drive, while the M motor for turning it. This solution considerably simplifies the maneuvering of the vehicle, although it requires a lot of attention, especially when reversing. The model is controlled by SBrick and PS4 pad. Caterpillars: I decided to put a separate paragraph. One tape consists of 214 elements and the whole caterpillar has 617. As you can guess, it is a lot of blocks. Why did not I use ordinary caterpillars since mine still have 5 studs? Look. The original belts with the tread are thick at almost a stud. The original lego links do not resemble their appearance and are too thin. The whole suspension is based on dishes wrapped with lego chains. This is another procedure that was supposed to add a maximum of realism and be as technically efficient as possible. On the inside I put on the elastics to limit the slippage of the rear drive wheels. In addition, each tension belt is the hardest spring of small Lego shock absorbers. We managed to push the suspension on the cradles, which, however, has limited room for maneuver and shock-absorbed rear axles. Each of them is completely autonomous and can even operate unbuckled from the tractor. It is possible to change their spacing without interfering with the tractor's construction. Maybe it will sound strange but I am really proud of them and in my opinion they could appear as a separate MOC. Challenger MT 865C caterpillars by Michał Skorupka (Eric Trax), on Flickr Additional functions One of the assumptions was to equip the tractor with a pneumatic system that was to eventually control the swivel plow. The idea was successfully implemented and packed under the hood. Compressor with two pumps driven by L engine and servo pneumatic valve. The whole is very efficient and works without the slightest objections. In addition, a power take-off shaft operating while driving, driven from a sub-tractor and a three-point suspension system lifted by a small linear actuator and M engine Kinze 1050 Grain Cart It is a very large Grain Cart that has a width of 3700 mm. So, outside of the USA and Canada, these trailers do not meet. Their use to collect the grain accumulated in the combine without stopping it, deliver and unload it onto a truck. Scaling the model I reduced its size using a ratio of 1:18 compared to the original. The trailer is available in three versions of the chassis. On tracks, on Softred wheels (balloons with limited pressure on the ground), Rowcrop (twin wheels). The natural choice would be the tracks but I wanted to use the tires from Claas. I also experimented with Power Puller tires, unfortunately the tractor did not want to move the trailer from the place, although it looked wonderful. The construction itself is not too complicated. In the middle there is an auger driven by the M engine and a unloading auger which is ready to work by large pneumatic cylinder. It works well, however, due to the angle of 180 degrees. With so few mechanisms, I focused on the appearance. Adding all additional equipment available in this model. Video: Congratulations to people who have read this entire description. Edited May 3, 20186 yr by eric trax
April 20, 20186 yr Jaw dropping as always! If it was not for the wheel of the trailer I would not have guessed this is Lego. My compliments for another fabulous creation ...
April 20, 20186 yr Top quality, and let people never forget to remain that level is always a challenge.
April 21, 20186 yr Another incredible build! The tractor is very smooth, the lines are excellent! Hard to tell that it's Lego... I did read the whole description! How much are the Claas tires stretched to fit the Power Puller wheels?
April 21, 20186 yr Absolute stunning work again Eric. Love all the details on the tractor and trailer.
April 22, 20186 yr Author Thank you for the positive response. I am glad that you like the model :) On 4/21/2018 at 6:26 AM, Leonardo da Bricki said: How much are the Claas tires stretched to fit the Power Puller wheels? The physical sizes are not much bigger. However, there is a big difference in appearance. On the PP rim, the tire seems wider and more massive than on the Xerion rim. I took pictures for comparison 18 hours ago, Edwin Korstanje said: Absolute stunning work again Eric. Love all the details on the tractor and trailer. @Edwin Korstanje I watched your ships and I also wanted to have a lot of barriers hahahah :D Edited April 22, 20186 yr by eric trax
April 22, 20186 yr @eric trax Thanks for the comparison photos! The Claas tires look awesome on those rims! I might have to get 4 of them...
April 24, 20186 yr seriously great build Can I ask how you got the black rigid hose (if that's what you used) to stay in shape for the hand rails? (hard 90 degree with no support) It seems like it may be a neat trick to use. Thank you.
April 24, 20186 yr This is really really good and there's no need to explain the use of your own caterpillars. I mean I never would because I can't be bothered. I am more concerned for the vehicle bodywork. Your caterpillars work very well and look awesome. But the whole thing and the trailer are marvelous. I can't stop looking at al the details. The trailer looks like the real thing.
April 24, 20186 yr Wow! This is really cool! Great details and looks like a fun build! Keep up the great work!
April 24, 20186 yr Author 14 hours ago, MangaNOID said: Can I ask how you got the black rigid hose (if that's what you used) to stay in shape for the hand rails? (hard 90 degree with no support) It seems like it may be a neat trick to use. Thank you. @MangaNOID The hose is heated with a lighter in the place where it is to be bent. Gives it a shape by hand and keep it until it cools down. You have to be careful because when the snake overheats, the bend is very ugly.
April 30, 20186 yr @eric trax do you have, or planning on making instructions for the Challenger?????
May 1, 20186 yr @eric trax, wow, you are on the Frontpage! Better resize those photos that are over 1024!
May 2, 20186 yr Author 15 hours ago, Milan said: @eric trax, wow, you are on the Frontpage! WOW THANKS! 15 hours ago, Milan said: Better resize those photos that are over 1024! Ok no problem :) On 4/30/2018 at 9:32 PM, Dafgek81 said: @eric trax do you have, or planning on making instructions for the Challenger????? @Dafgek81 Unfortunately, I do not have enough time to create instructions for my models :( Edited May 2, 20186 yr by eric trax
May 2, 20186 yr @eric trax unfortunately always the same story, when I see a good MOC, there are no instructions. I am more of a collector then a MOC builder, so I need instructions to rebuild these beauiful builds.
May 2, 20186 yr Phenomenal! Link for those too lazy to cut and paste: https://www.youtube.com/watch?v=mAsI2L8AUgc&t=
May 3, 20186 yr Green is better color. Overall, just impressive work! Superb job! Thats bigger than mini fig scale isn't it? Edited May 3, 20186 yr by ISDAvenger
May 3, 20186 yr Author 14 hours ago, ISDAvenger said: Green is better color. True :D IMG_0762 by Michał Skorupka (Eric Trax), on Flickr Edited May 3, 20186 yr by eric trax
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.