January 26, 20232 yr I haven't bought a 1:10 car before due to lack of mechanical interest but I really do like the colour!!! The issues with proportions (which aren't all that bad to me) all seem to come from the wheel arches being too big and having to fit the car shape around them, so it will be interesting to see if the wheels fit in the smaller wheel arches, and if suspension/steering geometry can be upgraded to prevent rubbing while still having a good (meaning possibly unrealistically large) amount of suspension travel. I suspect the way to do it will be to shorten the top wishbone and angle it upwards (move it's mounting point out and down) so the top edge of the wheel moves inward and under the wheel arch as the suspension moves.
January 26, 20232 yr 3 hours ago, allanp said: I haven't bought a 1:10 car before due to lack of mechanical interest but I really do like the colour!!! The issues with proportions (which aren't all that bad to me) all seem to come from the wheel arches being too big and having to fit the car shape around them, so it will be interesting to see if the wheels fit in the smaller wheel arches, and if suspension/steering geometry can be upgraded to prevent rubbing while still having a good (meaning possibly unrealistically large) amount of suspension travel. I suspect the way to do it will be to shorten the top wishbone and angle it upwards (move it's mounting point out and down) so the top edge of the wheel moves inward and under the wheel arch as the suspension moves. Well, the 1:10 wheels have a diameter of 68,8 mm. 9 stud arch has space of 72 mm, which leaves 1,6 mm space on each side. But that's not enough to accomodate steering, unless you use very thin walls?
January 26, 20232 yr Is the gap between the wheel arch and wheel that bad? I think it looks rather nice. But then again, I have learned to like the Subaru BRZ that have the same "issue". :)
January 27, 20232 yr 21 hours ago, zoo said: Is the gap between the wheel arch and wheel that bad? I think it looks rather nice. But then again, I have learned to like the Subaru BRZ that have the same "issue". :) It doesn’t bother me
February 4, 20232 yr Yey! black shock absorbers on the front too also looks like we get at least 2 of these in flat silver: https://www.bricklink.com/catalogItemIn.asp?P=32054&colorID=95&in=A I wonder if the steering wheel rotates as well as the HOG dial Edited February 4, 20232 yr by SNIPE
February 5, 20232 yr 14 minutes ago, msk6003 said: 5L, both end hm...that is what i least expected; something like this, only with joint at both end...
February 5, 20232 yr 14 hours ago, SNIPE said: I wonder if the steering wheel rotates as well as the HOG dial It just should, as it was pretty easy to implement in corvette. As I checked, it should be also possible in Bugatti Bolide, as front is built pretty the same.
February 5, 20232 yr 18 hours ago, SNIPE said: Yey! black shock absorbers on the front too That was obvious from the images so far. 18 hours ago, SNIPE said: also looks like we get at least 2 of these in flat silver: https://www.bricklink.com/catalogItemIn.asp?P=32054&colorID=95&in=A I wonder how you can tell it apart from LBG? The top end seems pretty LBG to me, and nothing would warrant flat silver in a hidden position. 18 hours ago, SNIPE said: I wonder if the steering wheel rotates as well as the HOG dial That's something pretty hard to see on the video, but maybe there's some movement in the cockpit as she steers the HoG.. I really could not tell though.
February 7, 20232 yr On 2/5/2023 at 1:21 PM, gyenesvi said: I wonder how you can tell it apart from LBG? Well, if you look at the connector pinhole with 2 pins that they are connected to, the connectors are way lighter gray than the pin 2L with bush Even more weirdly is the fact that the pins don't go anywhere else, they just go into the connector with 2 pins and thats it. I don't think I've seen that in an official lego technic set yet. Maybe lego star wars did it but that's not my forté Edited February 7, 20232 yr by SNIPE
February 14, 20232 yr looks like someone reviewed it edit: nope , never mind. it's just a premere video of a load of babble) Edited February 14, 20232 yr by SNIPE
February 19, 20232 yr 2:18 it looks like 5 stud axle with endings like part 32494. It looks useful, very useful. Edited February 19, 20232 yr by keymaker
February 19, 20232 yr 2 minutes ago, keymaker said: 2:18 it looks like 5 strud axle with endings like part 32494. It looks useful, very useful. I was watching the same thing .
February 19, 20232 yr On 2/5/2023 at 5:46 PM, msk6003 said: 5L, both end Now can I upload image? 1 hour ago, keymaker said: 2:18 it looks like 5 stud axle with endings like part 32494. It looks useful, very useful. Are you think this is that usefull than this? On 2/5/2023 at 6:05 PM, 1gor said: hm...that is what i least expected; something like this, only with joint at both end... After get least 4 of original I will cut it in half or order more cada's joint.
February 19, 20232 yr Hmm, I certainly am excited about any new suspension part, but it seems the application becomes very specific with the the joint part at both ends. It limits the use to only this suspension arm length. Again, I’m happy to be able to narrow an independent suspension width a little more, but it seems to be missing some flexibility.
February 19, 20232 yr 1 hour ago, msk6003 said: Are you think this is that usefull than this? After second thought I think it is not that useful...but we'll see. I still don't think this part will allow me to prepare narrow independent suspension, but I hope I will find good use for them.
February 19, 20232 yr In am excited for the 7L flip flop beam. Pretty sure it was first released in this set? Will be getting at least one set for sure.
February 19, 20232 yr 3 hours ago, keymaker said: 2:18 Here you can also see the diffuser is asymmetrical in panel usage... very unsatisfying!
February 19, 20232 yr 8 minutes ago, astyanax said: Here you can also see the diffuser is asymmetrical in panel usage... very unsatisfying! It's needed for the spoiler mechanism. Personally I'm going to wait for a proper review before giving my final opinion.
February 19, 20232 yr 11 minutes ago, Zerobricks said: It's needed for the spoiler mechanism. Personally I'm going to wait for a proper review before giving my final opinion. I understand that, but they should've used the shorter panels on the non-spoiler side as well then. But maybe it's just weird of me that I hate getting unequal amounts of left and right panels in a set?
February 19, 20232 yr 57 minutes ago, Alex Ilea said: In am excited for the 7L flip flop beam. Pretty sure it was first released in this set? Will be getting at least one set for sure. It was first released in Green in the one Monster Jam set this year, but are you seeing it in a more neutral color in this set?
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.