Help with identifying parts/sets!

[unclejeffie]

 

 

heya, trouble finding these minifigs, don't even know ef they are correct!

[Alexandrina]

What you have there is a motley selection of Star Wars figures:

You have the head and hair of Episode II Anakin from 2002 - this'll be from either set 7113 or set 7133.

This is paired with the body/legs of Darth Maul

You've also got the helmet of a Snowtrooper on the body of a Clone Trooper w/ Sand Green Markings

And the torso looks like Plo Koon - I'm not 100% on this one as I don't have a Plo Koon

[unclejeffie]

Thx, however the torso from darth maul is not the same, 

[Alexandrina]

Yes, well spotted! It appears to instead be the Emperor

[Takanuinuva]

These slopes exist in Sand Green but not in any actual sets? 

https://www.bricklink.com/v2/catalog/catalogitem.page?P=3678b&C=48#T=C&C=48

Usually with something like this. It's 1 or 2 bricklink sellers. But there 54 with this part. 

Was it a pick a brick piece?

As I do need this part in this color. But I always like to make sure it's officially existed. I don't like to use knockoff lego parts in my creations.

[Holodoc]

The are also sold in Europe only and partially in large quantities.
My bet: They have been available in the "Fabrik" in Legoland Germany. You can buy stuff by the weight there.

[Peppermint_M]

I miss Fabrik. 

[metalgeekzy]

1 hour ago, Takanuinuva said:

These slopes exist in Sand Green but not in any actual sets? 

https://www.bricklink.com/v2/catalog/catalogitem.page?P=3678b&C=48#T=C&C=48

Usually with something like this. It's 1 or 2 bricklink sellers. But there 54 with this part. 

Was it a pick a brick piece?

As I do need this part in this color. But I always like to make sure it's officially existed. I don't like to use knockoff lego parts in my creations.

With a little bit of paint it can be any color you want!

But seriously tho, i found it on Brickowl.

 

[antp]

The part existed with printing:

https://www.bricklink.com/v2/catalog/catalogitem.page?P=3678bpb043#T=C

https://www.bricklink.com/v2/catalog/catalogitem.page?P=3678bpb041#T=C

So at least Lego officially produced it in that color.

They probably got rid of the excess produced and still unprinted, sold in bulk.

Edited October 16, 2021 by antp

[Takanuinuva]

8 hours ago, antp said:

The part existed with printing:

https://www.bricklink.com/v2/catalog/catalogitem.page?P=3678bpb043#T=C

https://www.bricklink.com/v2/catalog/catalogitem.page?P=3678bpb041#T=C

So at least Lego officially produced it in that color.

They probably got rid of the excess produced and still unprinted, sold in bulk.

I forgot about that. It was used for the statue of liberty figure. 

Thx.

[tmtomh]

Hello all,

 

Apologies in advance if the answer is obvious (or if the more experienced users are sick of folks asking "what part is this?"  ). I'm trying to reverse-engineer a Spirited Away MOC for a loved one, and all I have to go on are a couple of photos posted online. I've got it mostly done, but I can't figure out what Lego parts the designer used for the spindly little arms in this photo. (This is Noface, for those familiar with the film.)

I have looked through the Technic, Bionicle, and Hero Factory sections of Bricklink Studio a few times, but I'm not seeing these parts. Perhaps I'm missing something obvious.

Thanks for any information or leads folks can provide!

[1963maniac]

 I remember them from Classic Space. You will find them in parts, arm on Bricklink.

Arm Grab Jaw, 4221; Arm Grab Jaw Holder, 4220; Arm Piece Straight with 2 and 3 Fingers, 3612

 

[tmtomh]

That's it! Thank you so very much!

(Just found the "Retired and Miscellaneous" category in Bricklink Studio and they are there.)

[Faefrost]

The hands and arms are long obscoleted finger hinge parts. Seen in many things such as old school space and divers. 

These are the hands https://www.bricklink.com/v2/catalog/catalogitem.page?P=4221&idColor=11#T=C&C=11 plus these https://www.bricklink.com/v2/catalog/catalogitem.page?P=4220&idColor=9#T=C&C=9

These are the bulk of the arms https://www.bricklink.com/v2/catalog/catalogitem.page?P=3612&idColor=9#T=C&C=9 plus  https://www.bricklink.com/v2/catalog/catalogitem.page?P=6048&idColor=11#T=C&C=11 and https://www.bricklink.com/v2/catalog/catalogitem.page?P=6217&idColor=11#T=C&C=11

Be warned that these older finger hinge parts are quite fragile. Which is why they were discontinued 25 years ago. 

[Ajf350d]

Those bring back memories!

I used to combine them all into one really long arm, and I seem to recall you can add an opposing ’claw’ as well to make a grab at the end.
These would be good today if they were still made. Good arms for some of the Marvel figures etc.

[AmperZand]

Deleted comment as thread merged by mods.

Edited November 4, 2021 by AmperZand

[BKu]

Is there someone who knows the Bricklink number of below piece?
No number is printed into the piece, tried to locate it by shape, studs, size, type, but nothing found.

 

Edited November 9, 2021 by BKu
change of picture

[Darkdragon]

10 minutes ago, BKu said:

Is there someone who knows the Bricklink number of below piece?

I believe that is  Tyco element, not a LEGO element.

[Exetrius]

@BKu @Darkdragon Think it is this LEGO element: https://www.bricklink.com/v2/catalog/catalogitem.page?P=6044&idColor=3#T=C&C=3 

[Darkdragon]

I think you are correct @Exetrius

[BKu]

@Exetrius : Yes this is the piece. Thanks for your help. I looked in the same type of pieces (slope section), but couldn't find it.

Many thanks,

[Maple]

I didn't know there was a whole post. That will be handy.

[Wenix]

Hey does anybody know what this trans light blue  shaped like ball elemnet id is?

Thank u for letting me know 😁.

 

[Peppermint_M]

That looks like one of these.

[Wenix]

20 hours ago, Peppermint_M said:

That looks like one of these.

I dont think it is cuz u cannot see the clips on the back.. Maybe he took the picture in that angle that u cannot see it but i think its a different part..